Tamiya TT02 Thread
|
|||
#826
Tech Addict
iTrader: (1)
The HPI Vintage wheels are designed to be used with the HPI Vintage tires. If your local class has a spec touring car tire, they most likely won't be able to be mounted on the HPI Vintage wheels.
HPI does make a 26mm "stock car" wheel in black that is designed for standard touring car tires. The part number is 3741. Here is a link on Tower (http://www3.towerhobbies.com/cgi-bin...?&I=LXNV38&P=7)
HPI does make a 26mm "stock car" wheel in black that is designed for standard touring car tires. The part number is 3741. Here is a link on Tower (http://www3.towerhobbies.com/cgi-bin...?&I=LXNV38&P=7)
#827
Tech Adept
Racing a tt-02 type s in the TCS?
I was looking through the Tamiya Championship Series rules and I don't see a class where this variation of the car could be competitive. I was thinking GT Pro spec, but the type s is not allowed there. Can anyone think of a TCS class where this car could be geared/motored competitively?
#828
Tech Initiate
I was looking through the Tamiya Championship Series rules and I don't see a class where this variation of the car could be competitive. I was thinking GT Pro spec, but the type s is not allowed there. Can anyone think of a TCS class where this car could be geared/motored competitively?
#829
Tech Adept
Tires are not the problem. It is more of an issue of getting the gear ratio down into the 3.5 to 4.0 FDR for a brushless setup without using non-Tamiya parts which is not allowed according to TCS rules. Of course you can run a silver can 540J in the gt3 class and gearing won't be an issue, but you will need to run against others chassis with 21.5 brushless motors. There is no way a 540J motor is anywhere near the speed of a 21.5, a 25.5 maybe, but not a 21.5.
#830
Tech Master
Thread Starter
Tires are not the problem. It is more of an issue of getting the gear ratio down into the 3.5 to 4.0 FDR for a brushless setup without using non-Tamiya parts which is not allowed according to TCS rules. Of course you can run a silver can 540J in the gt3 class and gearing won't be an issue, but you will need to run against others chassis with 21.5 brushless motors. There is no way a 540J motor is anywhere near the speed of a 21.5, a 25.5 maybe, but not a 21.5.
http://www.thercracer.com/2013/07/ho...inky-with.html
#831
Tech Adept
I managed a FDR of 4.35 without any mods. Assuming you do not have to use Tamiya Spur gears you can do this.
http://www.thercracer.com/2013/07/ho...inky-with.html
http://www.thercracer.com/2013/07/ho...inky-with.html
BTW, I saw your site and you have some great info on it about the tt-02.
#832
Tech Adept
just bought a type S after the shops restocked it then i remembered my dilemma last time
type R has a 3degree toe in rear hubs as standard and type S only has a 2.5degree toe (as an aftermarket option) but the type S also has a 3degree toe in in the form of a steel suspension kit?
so if i used that suspension kit on the type S, would i get a 3 degree toe in, similar to the type R?
I bought the type S because i couldnt find it last time to i took the type R and now I am wondering if i should sell it or keep in/built it.
type R has a 3degree toe in rear hubs as standard and type S only has a 2.5degree toe (as an aftermarket option) but the type S also has a 3degree toe in in the form of a steel suspension kit?
so if i used that suspension kit on the type S, would i get a 3 degree toe in, similar to the type R?
I bought the type S because i couldnt find it last time to i took the type R and now I am wondering if i should sell it or keep in/built it.
#833
Tech Adept
If you use the 54634 rear steel mount it will increase the Type S rear toe by 0.5 degree to give 3 degrees. The main point of that mount though is to allow you to fit the rebound stoppers which then allow use of the droop screws. I fitted this to my Type S but IMHO it made the car much worse to drive as limiting droop caused the rear end to break away off power into corners. So any advantage the extra .5 degree toe gave was wasted. My Type S is lovely to drive on standard settings. I just hopped up other parts instead.
#834
Tech Adept
If you use the 54634 rear steel mount it will increase the Type S rear toe by 0.5 degree to give 3 degrees. The main point of that mount though is to allow you to fit the rebound stoppers which then allow use of the droop screws. I fitted this to my Type S but IMHO it made the car much worse to drive as limiting droop caused the rear end to break away off power into corners. So any advantage the extra .5 degree toe gave was wasted. My Type S is lovely to drive on standard settings. I just hopped up other parts instead.
so the steel part only gives an additional 0.5deg?
the description is quite misleading "Rear plate gives a setup with 3 degrees of toe-in for excellent stability. "
#836
Tech Master
Thread Starter
The TT02-S has 2.5 degrees of toe in with the rear plate that is included.
A std TT02 has 0 degrees of toe in. Unless you buy the hop-up rear hubs (they give you toe in at the rear of 2.5 degrees) or if you buy the TT02-S hop up suspension set which gives you 3 degrees.
As a side note, the hop-up suspension set also allows you to add droop limiters to your TT02-S which makes things easier.
Sorry no, they just replace the plastic part, there is no nut to go under the chassis. How have you damaged that part of the chassis? You didnt use threadlock on the parts or an electric screw driver?
#837
Tech Master
iTrader: (15)
The hop up TT02-S steel rear plate gives you 3 degrees of rear toe-in.
The TT02-S has 2.5 degrees of toe in with the rear plate that is included.
A std TT02 has 0 degrees of toe in. Unless you buy the hop-up rear hubs (they give you toe in at the rear of 2.5 degrees) or if you buy the TT02-S hop up suspension set which gives you 3 degrees.
As a side note, the hop-up suspension set also allows you to add droop limiters to your TT02-S which makes things easier.
Sorry no, they just replace the plastic part, there is no nut to go under the chassis. How have you damaged that part of the chassis? You didnt use threadlock on the parts or an electric screw driver?
The TT02-S has 2.5 degrees of toe in with the rear plate that is included.
A std TT02 has 0 degrees of toe in. Unless you buy the hop-up rear hubs (they give you toe in at the rear of 2.5 degrees) or if you buy the TT02-S hop up suspension set which gives you 3 degrees.
As a side note, the hop-up suspension set also allows you to add droop limiters to your TT02-S which makes things easier.
Sorry no, they just replace the plastic part, there is no nut to go under the chassis. How have you damaged that part of the chassis? You didnt use threadlock on the parts or an electric screw driver?
#838
Tech Master
Thread Starter
Ouch!
Luckily the replacement chassis are very cheap, it's just a pain taking it all out
Luckily the replacement chassis are very cheap, it's just a pain taking it all out
#839
Tech Adept
#840