FT sc10 4x4, exotek, v2 center diff and more
04-02-2013, 08:09 PM
#1
FT sc10 4x4, exotek, v2 center diff and more
SOLD. Selling my ft sc10 4x4. i bought it last spring. i race it once a week indoors on a small, tight indoor track with hard packed dirt. It has all of the factory team upgrades, including AE's blue aluminum bling, vts slipper, FT shocks, and chassis brace. This is a great truck that would put me in the top half, sometimes, top 3, of my club races, considering I'm only an average driver. It also has the following after market upgrades:
-rcshox v2 center diff (9/10 pins installed, 10th pin is in little baggy) (great upgrade that transfers power appropriately over the vts slipper; very useful)
-m2c toe block (great mod as can increase rear toe to 3.5 to throttle out of corners sooner and brake into turns later without the backend swinging around; alread set at 3.5)
-strc aluminum steering column (stock plastic ones have high risk of breaking; aluminum one is very durable)
-strc aluminum belt tensioner
-exotek chassis (puts extra weight down low for added performance in lower traction tracks; also helps keep truck from getting pushed around by heavier trucks compared to stock chassis)
-exotek steering rack
-exotek saddle pack mounts (modded to fit rx8 speedo) (aligns weight better for improved jumping)
-rpm frt and rear arms (better than stock arms as stock arms will warp)
-futaba servo (installed in feb 2013) high torque (bls 352 servo)
-servo extension to receiver
-box with all original parts (i.e. sway bars, stock body(not painted), extra shock pistons)
Other upgrades:
-8mm mod installed (great mod; see sc10 4x4; helped me lock in back end)
-rebuilt diffs (in feb 2013) that have extra shims from ae so they don't leak
-mounted JC gold bar codes (about 7 runs on them)
-full set of FT springs
Not installed:
-strc 0.5 degree rear hubs
-strc 0.0 degree rear hubs
-team orion vortex vst 550 4.0 turn motor (run once weekly since last spring to december 2012); still runs great; just wanted to run pro4 motor
-near complete set of Avid bearings for sc10 4x4
Here is the link to the pics: https://picasaweb.google.com/1122874...eat=directlink
PM me if interested
-rcshox v2 center diff (9/10 pins installed, 10th pin is in little baggy) (great upgrade that transfers power appropriately over the vts slipper; very useful)
-m2c toe block (great mod as can increase rear toe to 3.5 to throttle out of corners sooner and brake into turns later without the backend swinging around; alread set at 3.5)
-strc aluminum steering column (stock plastic ones have high risk of breaking; aluminum one is very durable)
-strc aluminum belt tensioner
-exotek chassis (puts extra weight down low for added performance in lower traction tracks; also helps keep truck from getting pushed around by heavier trucks compared to stock chassis)
-exotek steering rack
-exotek saddle pack mounts (modded to fit rx8 speedo) (aligns weight better for improved jumping)
-rpm frt and rear arms (better than stock arms as stock arms will warp)
-futaba servo (installed in feb 2013) high torque (bls 352 servo)
-servo extension to receiver
-box with all original parts (i.e. sway bars, stock body(not painted), extra shock pistons)
Other upgrades:
-8mm mod installed (great mod; see sc10 4x4; helped me lock in back end)
-rebuilt diffs (in feb 2013) that have extra shims from ae so they don't leak
-mounted JC gold bar codes (about 7 runs on them)
-full set of FT springs
Not installed:
-strc 0.5 degree rear hubs
-strc 0.0 degree rear hubs
-team orion vortex vst 550 4.0 turn motor (run once weekly since last spring to december 2012); still runs great; just wanted to run pro4 motor
-near complete set of Avid bearings for sc10 4x4
Here is the link to the pics: https://picasaweb.google.com/1122874...eat=directlink
PM me if interested
Last edited by Eaglesrx; 04-04-2013 at 06:02 PM.
04-03-2013, 10:11 AM
#3
If u de side to part her out I would like some of the parts c diff tow blocks rear hubs
04-04-2013, 05:05 PM
#7
Phu u have a pm
04-04-2013, 05:21 PM
#8
Pm phu
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
