staikosn1

Ok so lets see...
The weather in that weekend race will be cold without sun...
The race truck, is kind of open some quick parts, but not easy... So for sure Ill some more steering and the car has to be quick from corner to corner!!
Should i use purple springs with 450 silicone front and behind??

gaspar

iTrader: (2)

Hi
im waiting for my first nt1!!, can you guys recommend me an specific model of batt for the rx (life or lipo)? Any start up list of spares>? or hop ups?
thanks!

Yoshimon

i have tried Li-fe batteries for my NT1 but they are normally too long to have a perfect fit in size. Normally, my friends will cut off the protection plastic packing in order to put the battery in place. Better choose either Li-po (but you then require a voltage regulator) or the usual NIMH battery.

asw7576

Use dremel with flat bottom bit,

flattened the north and south corner of xray battery holder.

north corner [___________li-fe battery__________] south corner

bluer322

iTrader: (2)

Ues the Exceed lipo pack fits perfick.

rx7ttlm

iTrader: (30)

I would start with ralph burch's winternats setup and adjust from there.

gaspar

iTrader: (2)

Hi
do i need a regulator? do you have the model number?
thanks!1!

jca2000au

iTrader: (9)

It is XCEED not EXCEED.

Li-PO part number 105001
Voltage Regulator 105002

Factory Seal

iTrader: (29)

I ran the 2011 Spec today.....W/every mod!..LOL! It is a 2 day Event......We ran 3 qualifiers...
currently im sitting at TQ.....Donnie Thomson 23 laps.....5:12.856
running the 2011 spec,with Sirio Mills and pipes,savox servo's

this is a AWESOME hotrod.....

Xray pilot....Jason Lutz........22 laps..........5:11.360

.
Xray Pilot....Lee Thompson....21 laps.........4:59.887


Privateer......Kevin Stephens...21 laps.........5:09.183.....


we sdtill have another qualifer and the mains tomorrow...
Wish Me luck....

SOLOARTIST 702

good job

staikosn1

I finally ran this weekend again...
All racers had problems cause we had to
get used to the new truck line (if I say it correct)
THe car was good enough, I changed the suspensions positions more to vertical (minor change, but finally so big) , the R3 RC was to quick, and i had to loose the centax spring a 1/4 of hour...
I used 37-40 tires, but next time Ill use 35-37 for better grip... I have to admit that i didnt change the silicone in diffs for the race..
I ll do it next time!!!!
I started 4th in 2nd final...I finished 3rd, and took place place for 1st final...
Was last in 1st final in 14 cars,and i finished 8th!!
1,5 hour of racing this weekend, perfect for practice!!!

Cheers, Nick!

Factory Seal

iTrader: (29)

Well i was in the lead in the Main shortly....5 laps before they caught me.......they had a mishap in turn 1....LOL!


anyway,I ended up 3rd.....Flame out on pit #2...UGH!!....sat there for about 1min.........15min main......LOL!!

Had a blast and the car is unreal,and easy to drive...
the X-Ray Pilots got me this time.....Can't wait until the Nat's in Feb........

a few pics....

baldy

iTrader: (1)

could you please tell me what your track is built out of

Factory Seal

iTrader: (29)

the Track is built from 3inch plastics PVC,we make T's inserts,small curves and big,,and Bend at different angles...drill holes in the ends for strapping it together...we also use Plow disc with a slot for the pipe to fit in for stops fo sharp corners.....and lots of VHT!....LOL!
......loop is 4inch pipe.....Drivers Stand is 13ft off the ground and 30ft in length..........

BigDogRacing

iTrader: (12)

Actually it's 2.5" PVC conduit schedule 40.
The connectors are 2" sch. 40 PVC conduit with a small 2.5" sleeve in the center.

BTW Donnie- that guy smiling in the picture u posted is one handsome fella. He musta won?