Xray NT1
#5986
Tech Adept
iTrader: (8)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Below is a picture of the arm that attaches to the steering servo. The manual states that it should be 36mm. I measure it to be around 41mm. The part numbers are all correct so I was wondering if I will have any issues installing this or is this just an issue with the manual?
![](http://i41.photobucket.com/albums/e283/Remy27/0d4b5e44.jpg)
![](http://i41.photobucket.com/albums/e283/Remy27/affbb0d6.jpg)
Thanks
![](http://i41.photobucket.com/albums/e283/Remy27/0d4b5e44.jpg)
![](http://i41.photobucket.com/albums/e283/Remy27/affbb0d6.jpg)
Thanks
#5987
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
There should be a pair of shorter ball cups in BAG 07.
#5991
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
CSO 3.5mm Graphite Chassis 2011Spec
#5992
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
hi, just wanted to buy 3Racing Alum Front Solid Axle but can i use for that standard diff outdrive adapters 335071?
#5994
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I'm having trouble with the high dynamic clutch that came in the WC kit. I built it so it has 0.7mm clutch gap, and very little end play. When I went to break in the car I could not get the clutch to engage, I built the clutch with the 10.00mm gap between the clutch nut and end of the shaft, and even tried loosening the clutch nut to get an earlier engagement but nothing worked. Anybody have a solution this is pretty frustrating.
#5995
Tech Fanatic
iTrader: (18)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I'm having trouble with the high dynamic clutch that came in the WC kit. I built it so it has 0.7mm clutch gap, and very little end play. When I went to break in the car I could not get the clutch to engage, I built the clutch with the 10.00mm gap between the clutch nut and end of the shaft, and even tried loosening the clutch nut to get an earlier engagement but nothing worked. Anybody have a solution this is pretty frustrating.
#5996
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I'm having trouble with the high dynamic clutch that came in the WC kit. I built it so it has 0.7mm clutch gap, and very little end play. When I went to break in the car I could not get the clutch to engage, I built the clutch with the 10.00mm gap between the clutch nut and end of the shaft, and even tried loosening the clutch nut to get an earlier engagement but nothing worked. Anybody have a solution this is pretty frustrating.
#5997
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I got a hold of a friend that told me how to set it right, so its figured out now, thanks for the help.
#5999
Tech Rookie
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
has hudy/xray changed their materials recently? the spring steel parts seem more black in colour now where it used to be a more of a brown colour????
#6000
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I am looking for longer ball joints for bottom of shock.
I am trying to fit 4way xray shocks on another vehicle.
The spring sit really low on shock and only leaves a few threads to spin collar down for ride height. I rather not fabricate a new rear shock tower.
Are the balljoints for rear way bar the same diameter as shock balljoints? Hard to tell on xray site but they look a bit longer and accept 5.8mm ball.
Thanks
Jamie
I am trying to fit 4way xray shocks on another vehicle.
The spring sit really low on shock and only leaves a few threads to spin collar down for ride height. I rather not fabricate a new rear shock tower.
Are the balljoints for rear way bar the same diameter as shock balljoints? Hard to tell on xray site but they look a bit longer and accept 5.8mm ball.
Thanks
Jamie