Mini-96 World Challenge
#1516
Tech Initiate
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Hi Scionara05, you're absolutely right. The front bumper splitter jabs into the gap of RCP rails and puts the car to a complete stop.
Last edited by AlvBo; 09-11-2022 at 01:16 AM. Reason: Referenced the wrong part of front bumper.
#1517
Tech Initiate
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Hi everyone,
1. For box stock category, are we allowed to change the rear spoiler wings? e.g. Jomurema body with RTRC rear spoiler or Mclaren GT3 body with lexan rear spoiler.
2. Is there a technique to identify tire softness/ degree? i.e. I have a few pairs of PN tires (which I removed from purchased 2nd hand chassis). They are now mixed up in a bag and I don't know if they are soft, super-soft, mediums etc. so I can't pair them properly. I tried squeezing/stretching them and comparing them to the new tires that I have but I still can't make out what hardness they are (partially also because they are half-used). I don't want to throw the used ones away because they are still usable at 22.6mm.
1. For box stock category, are we allowed to change the rear spoiler wings? e.g. Jomurema body with RTRC rear spoiler or Mclaren GT3 body with lexan rear spoiler.
2. Is there a technique to identify tire softness/ degree? i.e. I have a few pairs of PN tires (which I removed from purchased 2nd hand chassis). They are now mixed up in a bag and I don't know if they are soft, super-soft, mediums etc. so I can't pair them properly. I tried squeezing/stretching them and comparing them to the new tires that I have but I still can't make out what hardness they are (partially also because they are half-used). I don't want to throw the used ones away because they are still usable at 22.6mm.
#1518
Tech Initiate
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Date- 15 Sep 2022
Location- Singapore
Race Time- 367.755 seconds
Fastest Lap- 4.140
Chassis- MR-03
Body- Jomurema
Wheelbase- 98mm
Tires- (Front PN Medium) / (Rear PN Soft)
Motor- Stock
Batteries- PN 750mAH
Front Springs- PN Green
T-Plate- PN Carbon #4
Motor Mount- MM stock
Dampener (If applicable)- Stock spring
Dampener Fluid (If applicable)- n.a.
Gearing- 7T Pinion / Stock gear diff
Notes- Tried front purple & white springs but went back to green springs.
====================
Date- 13 Sep 2022
Location- Singapore
Race Time- 379.451 seconds
Fastest Lap- 4.253
Chassis- MR-03
Body- Jomurema
Wheelbase- 98mm
Tires- (Front PN Medium) / (Rear PN Soft)
Motor- Stock
Batteries- PN 750mAH
Front Springs- PN Green
T-Plate- PN Carbon #4
Motor Mount- MM stock
Dampener (If applicable)- Stock spring
Dampener Fluid (If applicable)- n.a.
Gearing- 7T Pinion / Stock gear diff
Notes- Can’t upload photos yet.
Location- Singapore
Race Time- 367.755 seconds
Fastest Lap- 4.140
Chassis- MR-03
Body- Jomurema
Wheelbase- 98mm
Tires- (Front PN Medium) / (Rear PN Soft)
Motor- Stock
Batteries- PN 750mAH
Front Springs- PN Green
T-Plate- PN Carbon #4
Motor Mount- MM stock
Dampener (If applicable)- Stock spring
Dampener Fluid (If applicable)- n.a.
Gearing- 7T Pinion / Stock gear diff
Notes- Tried front purple & white springs but went back to green springs.
====================
Date- 13 Sep 2022
Location- Singapore
Race Time- 379.451 seconds
Fastest Lap- 4.253
Chassis- MR-03
Body- Jomurema
Wheelbase- 98mm
Tires- (Front PN Medium) / (Rear PN Soft)
Motor- Stock
Batteries- PN 750mAH
Front Springs- PN Green
T-Plate- PN Carbon #4
Motor Mount- MM stock
Dampener (If applicable)- Stock spring
Dampener Fluid (If applicable)- n.a.
Gearing- 7T Pinion / Stock gear diff
Notes- Can’t upload photos yet.
Last edited by AlvBo; 09-14-2022 at 09:48 AM.
#1519
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Hi everyone,
1. For box stock category, are we allowed to change the rear spoiler wings? e.g. Jomurema body with RTRC rear spoiler or Mclaren GT3 body with lexan rear spoiler.
2. Is there a technique to identify tire softness/ degree? i.e. I have a few pairs of PN tires (which I removed from purchased 2nd hand chassis). They are now mixed up in a bag and I don't know if they are soft, super-soft, mediums etc. so I can't pair them properly. I tried squeezing/stretching them and comparing them to the new tires that I have but I still can't make out what hardness they are (partially also because they are half-used). I don't want to throw the used ones away because they are still usable at 22.6mm.
1. For box stock category, are we allowed to change the rear spoiler wings? e.g. Jomurema body with RTRC rear spoiler or Mclaren GT3 body with lexan rear spoiler.
2. Is there a technique to identify tire softness/ degree? i.e. I have a few pairs of PN tires (which I removed from purchased 2nd hand chassis). They are now mixed up in a bag and I don't know if they are soft, super-soft, mediums etc. so I can't pair them properly. I tried squeezing/stretching them and comparing them to the new tires that I have but I still can't make out what hardness they are (partially also because they are half-used). I don't want to throw the used ones away because they are still usable at 22.6mm.
2. There are tools you can buy for this.
#1520
Tech Initiate
#1522
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Thanks for the link Chjosi! Those are VERY similar to the depth guage setup I use the reload ammo for my single shots, but with a finer tip. I'm going to try it out to see if it will work.
AlvBo, those are some GOOD TIMES!!!! Can't wait to see them after you have some time and practice under your belt! CCW is still kickin my arse!!!
Take Care and Drive Fast!
AlvBo, those are some GOOD TIMES!!!! Can't wait to see them after you have some time and practice under your belt! CCW is still kickin my arse!!!
Take Care and Drive Fast!
#1523
Tech Initiate
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Thanks for the link Chjosi! Those are VERY similar to the depth guage setup I use the reload ammo for my single shots, but with a finer tip. I'm going to try it out to see if it will work.
AlvBo, those are some GOOD TIMES!!!! Can't wait to see them after you have some time and practice under your belt! CCW is still kickin my arse!!!
Take Care and Drive Fast!
AlvBo, those are some GOOD TIMES!!!! Can't wait to see them after you have some time and practice under your belt! CCW is still kickin my arse!!!
Take Care and Drive Fast!
#1524
#1525
Tech Initiate
#1526
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I am seriously challenged with this layout CCW! I had my fastest lap CW after getting the disk damper setup at 4 seconds flat with only twice needing to reverse in 75 laps! But CCW I can't turn 5 laps without sticking it in the wall and my times are almost as slow as I was when I started! I'll try for 75 laps in the Stock class, but I'm not promising ANYTHING!! LOL
#1527
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Class- Stock
Date-09/28/22
Location- Central Texas
Race Time- 7:23 / 443.0 seconds
Fastest Lap- 4.75 seconds
Chassis- MR-03
Body- Jomurema
Wheelbase- 98mm
Tires- F- Kyo low height slicks 30* / R- PN KS Radial Soft
Motor- stock
Batteries- Pn 900maAh
Front Springs- green
T-Plate- #5 Carbon
Motor Mount- MM stock
Dampener (If applicable)- PN MR2061 Graphite Disk Damper (both disks, purple springs), PN MR2161 Dual Spring center shock (silver springs)
Dampener Fluid (If applicable)- none
Gearing-8T Pinion/Stock gear diff
Notes- Disk damper/dual spring shock CALMED the car down considerably! I continued to have problems CCW. I ran CW directly after running my posted CCW, and had my fastest 75 laps and turned 3.75, 3.76, & 3.79 in a row! My fastest laps EVER!!! I'm confused why I'm having soo much trouble CCW. Ready for new layout and CW!
![](https://cimg0.ibsrv.net/gimg/www.rctech.net-vbulletin/768x1024/september_laps_9b4a95a673769cc56bba2b35283bfd7ce5d08c26.png)
![](https://cimg2.ibsrv.net/gimg/www.rctech.net-vbulletin/2000x1493/september_pic_6d201496d5716d010439f820eafbec3cbf761d24.jpg)
Date-09/28/22
Location- Central Texas
Race Time- 7:23 / 443.0 seconds
Fastest Lap- 4.75 seconds
Chassis- MR-03
Body- Jomurema
Wheelbase- 98mm
Tires- F- Kyo low height slicks 30* / R- PN KS Radial Soft
Motor- stock
Batteries- Pn 900maAh
Front Springs- green
T-Plate- #5 Carbon
Motor Mount- MM stock
Dampener (If applicable)- PN MR2061 Graphite Disk Damper (both disks, purple springs), PN MR2161 Dual Spring center shock (silver springs)
Dampener Fluid (If applicable)- none
Gearing-8T Pinion/Stock gear diff
Notes- Disk damper/dual spring shock CALMED the car down considerably! I continued to have problems CCW. I ran CW directly after running my posted CCW, and had my fastest 75 laps and turned 3.75, 3.76, & 3.79 in a row! My fastest laps EVER!!! I'm confused why I'm having soo much trouble CCW. Ready for new layout and CW!
![](https://cimg0.ibsrv.net/gimg/www.rctech.net-vbulletin/768x1024/september_laps_9b4a95a673769cc56bba2b35283bfd7ce5d08c26.png)
![](https://cimg2.ibsrv.net/gimg/www.rctech.net-vbulletin/2000x1493/september_pic_6d201496d5716d010439f820eafbec3cbf761d24.jpg)
#1528
Tech Addict
iTrader: (1)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I'm back! Sorry for the long absence! I had several ailments earlier in the year and a new job that has kept me preoccupied. I was only able to get a few runs in this month, but hope to be more active going forward. I'll be posting the new layout for October tomorrow. Get those last minute runs in and posted by midnight EDT tonight!
#1529
Tech Addict
iTrader: (1)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Class-Box Stock
Date-9/18/22
Location-Winston-Salem, NC
Race Time-277.4
Fastest Lap-3.48
Chassis-MR-03 ASF
Body-McLaren F1 LM
Wheelbase-98mm
Tires-K30LH fronts, Marka V1R10 rears
Motor-Stock
Batteries-TRP 747s
Front Springs-PN Red
T-Plate-Kyosho Carbon Med
Motor Mount-Stock MM
Dampener (If applicable)-None
Dampener Fluid (If applicable)-K 15k grease on top shock
Gearing-Stock Gear Diff/7T pinion
Notes-No changes from previous month. Only a couple of runs with this car.
![](https://cimg2.ibsrv.net/gimg/www.rctech.net-vbulletin/934x959/capture_b74478f22d403b492939d0b91d0506751bed81e9.png)
Date-9/18/22
Location-Winston-Salem, NC
Race Time-277.4
Fastest Lap-3.48
Chassis-MR-03 ASF
Body-McLaren F1 LM
Wheelbase-98mm
Tires-K30LH fronts, Marka V1R10 rears
Motor-Stock
Batteries-TRP 747s
Front Springs-PN Red
T-Plate-Kyosho Carbon Med
Motor Mount-Stock MM
Dampener (If applicable)-None
Dampener Fluid (If applicable)-K 15k grease on top shock
Gearing-Stock Gear Diff/7T pinion
Notes-No changes from previous month. Only a couple of runs with this car.
![](https://cimg2.ibsrv.net/gimg/www.rctech.net-vbulletin/934x959/capture_b74478f22d403b492939d0b91d0506751bed81e9.png)
![](https://cimg2.ibsrv.net/gimg/www.rctech.net-vbulletin/1280x958/569cf1a9_9bb6_4146_a448_8cdda81213ff_02f3e5a9877f2d56fc021a06feabe0a57f69d435.jpeg)
#1530
Tech Addict
iTrader: (1)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Class-RM Porsche Cup Class
Date-9/18/22
Location-Winston-Salem, NC
Race Time-288.2
Fastest Lap-3.56
Chassis-MR-03 ASF
Body-911 GT1
Wheelbase-90mm
Tires-K30LH fronts, Marka 10 rears
Motor-Stock
Batteries-TRP 747s
Front Springs-ATM Deep Blue (Soft)
T-Plate-Kyosho Carbon Soft
Motor Mount-Stock RM
Dampener (If applicable)-None
Dampener Fluid (If applicable)-None
Gearing-Stock Gear Diff/7T pinion
Notes-No changes. Only a couple of runs this month.
![](https://cimg7.ibsrv.net/gimg/www.rctech.net-vbulletin/936x959/capture_01e805b2a83f2a7be9b077db39a31a40eec70c38.png)
Date-9/18/22
Location-Winston-Salem, NC
Race Time-288.2
Fastest Lap-3.56
Chassis-MR-03 ASF
Body-911 GT1
Wheelbase-90mm
Tires-K30LH fronts, Marka 10 rears
Motor-Stock
Batteries-TRP 747s
Front Springs-ATM Deep Blue (Soft)
T-Plate-Kyosho Carbon Soft
Motor Mount-Stock RM
Dampener (If applicable)-None
Dampener Fluid (If applicable)-None
Gearing-Stock Gear Diff/7T pinion
Notes-No changes. Only a couple of runs this month.
![](https://cimg7.ibsrv.net/gimg/www.rctech.net-vbulletin/936x959/capture_01e805b2a83f2a7be9b077db39a31a40eec70c38.png)
![](https://cimg2.ibsrv.net/gimg/www.rctech.net-vbulletin/1280x958/e8a6b0f5_43e2_4980_a017_80ccde95d2a0_796ee1a677f087ee0d93f52c494713293d888d75.jpeg)