Hpi Pro 4
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
what does the Heavy Duty, Self Lubricating Ball Cups do????
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
Tech Addict
iTrader: (29)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
To adjust the diffs, do like above by popping the ball end then use the cheap "L" allen key from the kit to adjust the front is the same, if you use this allen key instead, you don't have to remove the hinge pin.
Tech Master
iTrader: (80)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Where can I find the TIR Titanium Bones for the front of the Pro 4? Any help would be appreciated.
Tech Apprentice
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
You can find titanium dogbones on www.rc-mushroom.com in the car hopup section from Square. They're spendy though! $42!
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by atomic80
You can find titanium dogbones on www.rc-mushroom.com in the car hopup section from Square. They're spendy though! $42!
Look under "manufacturer" for TIR Titanium Racing.
![Wink](https://www.rctech.net/forum/classic_images/smilies/wink.gif)
Tech Apprentice
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Sorry about that...I read it too fast. Didn't see the "TIR" part. Well, there's an alternative.
![Roll Eyes (Sarcastic)](https://www.rctech.net/forum/classic_images/smilies/rolleyes.gif)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by atomic80
Sorry about that...I read it too fast. Didn't see the "TIR" part. Well, there's an alternative. ![Roll Eyes (Sarcastic)](https://www.rctech.net/forum/classic_images/smilies/rolleyes.gif)
![Roll Eyes (Sarcastic)](https://www.rctech.net/forum/classic_images/smilies/rolleyes.gif)
![Smilie](https://www.rctech.net/forum/classic_images/smilies/smile.gif)
Tech Master
iTrader: (1)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
does everyone think that the 05 model has fixed some problems with the chassis tweak?? i mean i have made all the mods on my top deck that the new model has and it still tweaks, but i dont have the alloy camber plates.. so im not sure wether to upgrade or what any thoughts??
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Extremely sorry if this has been asked, but does anyone have a link to instructions so i can mod my upper deck like on hara's pro 4? and also the parts (screws) needed?
Thanks
Thanks
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by adamkerrnz
Extremely sorry if this has been asked, but does anyone have a link to instructions so i can mod my upper deck like on hara's pro 4? and also the parts (screws) needed?
Thanks
Thanks
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I seem to read this all the time. I don't hit the walls as much anymore so should it be a problem for me?
Tech Fanatic
iTrader: (50)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Recently picked up a Pro 4. I need a general setup for asphalt track on rubber tires (cs-27s). I am using a diff in the front. Also have the 2.5mm top deck on the car(to help with tweak).
I have all the toe plates, anti-squat plates and spring so hopefully I can do whatever setup is recommended.
Can someone point me to a good one?
thanks.
I have all the toe plates, anti-squat plates and spring so hopefully I can do whatever setup is recommended.
Can someone point me to a good one?
thanks.
Tech Addict
iTrader: (3)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I have run the kit setup with really good results. But, if you want to try some different things try some of the setup on HPI's site.
http://www.hpiracing.com/setups/su-m.php#Pro%204
http://www.hpiracing.com/setups/su-m.php#Pro%204
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by newnew
what does the Heavy Duty, Self Lubricating Ball Cups do???? ![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
If the track is smooth, stick to around 5-5.5mm RH, 3-3.5 droop, I had AE red/front, blue/rear springs, 1.5 front block, 2.5 rear block.Your standard camber setting. Keep an eye on the droop grubs. If who-ever built the kit was sloppy with a tap the grubs may be loose. NOT GOOD.
![Nodding](https://www.rctech.net/forum/classic_images/smilies/nod.gif)
Last edited by coastaltony; 10-13-2007 at 05:30 AM.