Hpi Pro 4
Yeah my car has flipped over do to bumps by other cars, i've hit boards head on. But if i get hit at low speeds during a turn then it starts clicking.
Yeah my car has flipped over do to bumps by other cars, i've hit boards head on. But if i get hit at low speeds during a turn then it starts clicking.
i will be running my pro4 in the 540 'sliver can' class on the weekend,what sort of gearing do you guys reckon? should i keep it the same as the 27t class?
Tech Fanatic
iTrader: (1)
Moot ....Na Stock gearing is to low...On a fast flowing track guys at our track run up to 50mm rollout.
Moot : For a normal Tamiya type 540 2xvent Johnson motor, I used from 47-51mm rollout ... depending on track. Using 60T(48P) spur & from 36T-40T(48P) on Jaco Nitro Shoes foams. Further 60wt-front&50wt-rear oil with AE red-front&AE gold-rear springs. Remember that especially with stock your drive-train has to be 200% effiecient as every little part has an influence. If you are looking at hop-ups, definitely consider the Square TI input shafts; carbon drive shaft; ceramic bearings (I like ACER). Use a piece of car shammy with the vent holes cut open and keep it wet before going on the track(I use a mediacal syringe with water). This is cheap, ligther than a heatsink and even try Nitro Freeze spray to keep it really cool. Also change you pivot blocks from the stock set to 0deg-front & 1deg-rear.
Hope it helps!
Vance
Hope it helps!
Vance
Tech Fanatic
iTrader: (40)
Originally posted by Mach10_shooter
I thought there might be more interest in this. Anyone else?
Chris
I thought there might be more interest in this. Anyone else?
Chris
Here is a battery strap I've come up with. Is anyone interested?
Last edited by Mach10_shooter; 01-02-2011 at 08:38 PM.
Wow that looks really good
Tech Adept
Mach10_shooter:
Have you seen the Schumacher carbon battery-straps?
They look quite similar to your design, with a vertically mounted piece along the strap, with the shape of the battry-cells macined. If you can see what i'm trying to explain.
Have you seen the Schumacher carbon battery-straps?
They look quite similar to your design, with a vertically mounted piece along the strap, with the shape of the battry-cells macined. If you can see what i'm trying to explain.
Tech Fanatic
iTrader: (40)
Thank you, I am also working on a bumper brace, camber link mounting plate made from 3.1mm material, and a custom front sway bar mount that mirrors the sway bar mount over on top of the upper deck...
Tech Fanatic
iTrader: (40)
Originally posted by Erlend
Mach10_shooter:
Have you seen the Schumacher carbon battery-straps?
They look quite similar to your design, with a vertically mounted piece along the strap, with the shape of the battry-cells macined. If you can see what i'm trying to explain.
Mach10_shooter:
Have you seen the Schumacher carbon battery-straps?
They look quite similar to your design, with a vertically mounted piece along the strap, with the shape of the battry-cells macined. If you can see what i'm trying to explain.
Tech Addict
iTrader: (3)
Originally posted by Mach10_shooter
Here is a battery strap I've come up with. Is anyone interested?
Here is a battery strap I've come up with. Is anyone interested?
Tech Fanatic
iTrader: (40)
Bumper brace
Here's my bumper brace.
Last edited by Mach10_shooter; 01-02-2011 at 08:38 PM.
What's wrong with strapping tape?!
Tech Addict
iTrader: (3)
Re: Bumper brace
Originally posted by Mach10_shooter
Here's my bumper brace.
Here's my bumper brace.
How Much would the Bumper brace cost???