5LikesSC10 4x4 Thread
12-13-2011, 08:22 PM
it is most likely your belt slipping... dial your breaks down until the sound goes away
12-13-2011, 08:30 PM
12-13-2011, 08:31 PM
http://teamassociated.com/pictures/p...4/91054_md.jpg
what are the small 1 2 clips for i dint see the in the book?
what are the small 1 2 clips for i dint see the in the book?
12-13-2011, 09:04 PM
Tech Regular
iTrader: (14)
Lol
12-13-2011, 09:09 PM
quick ?
just purchased my sc10 4x4, what is the most needed spare parts for this truck
12-13-2011, 09:10 PM
Slipper pads. LOL
12-13-2011, 09:17 PM
thanks
that sounds like a good plan
12-13-2011, 09:19 PM
Thanks though!(I don't make any money off the braces. If I did i'd go mantis and make more parts.
)And Vegatron:
12-13-2011, 11:03 PM
12-13-2011, 11:13 PM
You are trying to compare a mature chassis, to a chassis still in it's infancy.
For example, I built an RC8Be recently. other than raising the rear links a hole, taking away some front droop and going to the longest wheelbase, it was darn good out of the box.
On the other hand, my SC104x was just a huge POS out of the box. It was a struggle not to give up on it and it's pretty good now.
Just keep things in perspective.
For example, I built an RC8Be recently. other than raising the rear links a hole, taking away some front droop and going to the longest wheelbase, it was darn good out of the box.
On the other hand, my SC104x was just a huge POS out of the box. It was a struggle not to give up on it and it's pretty good now.
Just keep things in perspective.
I have started running VTA at my local parking lot, with my old XXX-S G+ sedan. Fresh out of the box from the last time I ran it in 2003! I seriously put the radio gear in it and blew off the dust, I didn't even change the shock oil! But a little off - about .2 second a lap. So I went back and started reading the 800+ page thread, and remembered all the stuff other guys were trying back then. TL developed that chassis almost all the way to the end. Reading that thread reminds me of this one, except I could just skip to the end if I wanted to.
Nicely done. I lol'd.
12-13-2011, 11:18 PM
http://www.rctech.net/forum/9084333-post1.html
If you decide to run a 540 motor, you'll need a Yeah Racing fan.
If you decide to run a 550 or a four pole motor, you'll need a slipper upgrade. Either the Mac The Knife slipper basket, or the Mantis garodiscs.
I have not broken anything in this truck, nothing, not once.
12-14-2011, 12:32 AM
Sad Panda.
'night all.
Edit: It's a good/bad thing hardly anyone needed pinned setups from me. I have an asinine amount of Rear Topshafts sitting in my box.
12-14-2011, 03:49 AM
FYI Everyone:
A-main
Horizon Hobby
Tower Hobbies
ALL are doing free shipping over $99.00 till the 15th or so.
Edit: Just realized Horizon doesn't matter for this truck... But... meh.
A-main
Horizon Hobby
Tower Hobbies
ALL are doing free shipping over $99.00 till the 15th or so.
Edit: Just realized Horizon doesn't matter for this truck... But... meh.
12-14-2011, 10:26 AM
The bolts are lighter, but you don't want to take weight off the truck, you need to add more weight. I don't know about everyone else, the Losi trucks can push an SC10 4x4 out out the way very easily. Spend the money on Mantis new center diff, Coyote's chassis brace, Exotek chassis, or something that will make the truck run better.
12-14-2011, 10:36 AM
