SC10 4x4 Thread
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I have the reedy saddle pack #627... stupid question here....do these get charged individually?
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Not sure if they can be charged separately. I would assume so. But verify that first.
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
I run primarily on outdoor tracks here, I wish I had more indoor.
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Yea you always want to run packs as a single unit when using and balance charging. This way each cell is charged to the same level.
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
got my ft done sans body. right now it has a havoc pro sc (non x drive) and a viper 5.0 l, strc steering kit along with strc pulleys, rcshox v2 pistons. my next paycheck ill probably get a rx8 esc. i have not tried tekin yet, i had the havoc sitting around.
it was a fun build and thank god my roommate has a cordless power drill. i got my diff dilemma solved, one of the 4x4 guys at the track built a spare gear diff with me so i could see what it should look like and how it should feel when done. after a few runs on street tires on the street, i wound up with a 13 tooth pinion and temping out at 135 after 6 minutes of hard running. should be close for the track this upcoming week.
it was a fun build and thank god my roommate has a cordless power drill. i got my diff dilemma solved, one of the 4x4 guys at the track built a spare gear diff with me so i could see what it should look like and how it should feel when done. after a few runs on street tires on the street, i wound up with a 13 tooth pinion and temping out at 135 after 6 minutes of hard running. should be close for the track this upcoming week.
![Rotating Tire](https://www.rctech.net/forum/classic_images/smilies/tire.gif)
Tech Master
iTrader: (28)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Well went to my first 1/8 track today.... Didn't go so well. Track was loose and bumpy. Need some 2 stage pistons! Found the truck ran much better without sway bars.
![](https://lh4.googleusercontent.com/-zQizVnSmB7U/T4DqgiuBZQI/AAAAAAAAAi4/3ggK34CDzmE/s912/DSC00074.JPG)
![](https://lh6.googleusercontent.com/-8J-QwKQkxB0/T4DqoaAQfZI/AAAAAAAAAjs/C80VUt22ae0/s912/DSC00080.JPG)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I did not order a balance charge harness....and these have no balance ports...it looks like the reedy harness has 4mm bullets on end of balance leads...do these get plugged into where the jumper wire plugs?
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
OMG Evil I would love to run that track.
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
do you have the leads to plug in?
Tech Master
iTrader: (28)
Tech Master
iTrader: (28)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
It's a lot looser than it looks. Most run city blocks.
Have any setup suggestions? Doesn't help that I'm not a very good driver but a good setup can't hurt. BTW the A main was all LOSIs
Have any setup suggestions? Doesn't help that I'm not a very good driver but a good setup can't hurt. BTW the A main was all LOSIs
![Frown](https://www.rctech.net/forum/classic_images/smilies/frown.gif)
Tech Master
iTrader: (28)