Tamiya TRF415
Tech Elite
iTrader: (6)
Originally Posted by Eirik
I tested with both D-D blocks up front and B-A and ended up running the later as it gave me more steering! (used 6mm hexes)
In the rear I used the stock D-XB.....
The long arms runs too tight on carpet (stops in the corners) The short arms makes the car allot freer and it steers better, even when it slides
I have even been running the short arms outdoors lately, FASTER!!
In the rear I used the stock D-XB.....
The long arms runs too tight on carpet (stops in the corners) The short arms makes the car allot freer and it steers better, even when it slides
I have even been running the short arms outdoors lately, FASTER!!
Tech Elite
Join Date: Mar 2004
Location: MOOD;; feeling good not racing ,saving shed loads of money,lovely Tan i have aswell
Posts: 4,762
Originally Posted by TRF415boy
yep, 2 degrees rear toe in total, well enough for 19T...
but then i remembered i have the evo 4 blocks here so i`m using them instead
2.5 rear toe in & -5 degree toe out i`m trying ,i should be in the evo 5 thread but i`m talking to you now ,so here i`m am
Tech Master
iTrader: (2)
Cheers people, when i get some more 'moneys' i might give the short arms a try ,also is there anything i should watch out for in the MRE build.
Cheers, Charles
Cheers, Charles
Which suspension blocks do you use to run the short arms? All numbers for the blocks get confusing.
Tech Apprentice
Ok I don't know if anyone has asked this but here goes on marc's vegas setup he has a 2.2mm swaybar on the front what brand is this or did he make it himself.
Originally Posted by MR JOLLY
was going to put 1mm shims under pivot blocks to raise the roll centre (to act faster)
but then i remembered i have the evo 4 blocks here so i`m using them instead
2.5 rear toe in & -5 degree toe out i`m trying ,i should be in the evo 5 thread but i`m talking to you now ,so here i`m am
but then i remembered i have the evo 4 blocks here so i`m using them instead
2.5 rear toe in & -5 degree toe out i`m trying ,i should be in the evo 5 thread but i`m talking to you now ,so here i`m am
2.2mm Sway bar was a prototype and has never been made production. You can make you own. Good Luck with that
Randy Just get somes spares from your roomate LOL I heard David Jun may drive out Tuesday to give you clowns a hand, since he knows alot about foam tires LOL
Originally Posted by Jimmy Jacobson
Randy Just get somes spares from your roomate LOL I heard Flywheel may drive out Tuesday to give you clowns a hand, since he knows alot about foam tires LOL
As for me...I get to run "Old-Type"
I just loaded my new ipod with some junk so I can be anti-social in Vegas! J/K...if anybody needs help, please introduce yourself. I promise that I am usually not as busy as I look.
Tech Elite
Join Date: Mar 2004
Location: MOOD;; feeling good not racing ,saving shed loads of money,lovely Tan i have aswell
Posts: 4,762
Originally Posted by TRF415boy
what car is this for ?
Tech Master
iTrader: (12)
Please, I need the best shop for 415 parts URGENT
Hi Guy's
I really need your help fast I need several parts for my 415 MS and some square parts.
Does anyone know a shop that sends fast to australia and must take Pay pal
I need aftermarket Bumper and suspension arms number Tamiya 51104 Plus some suspension mounts
PLEASE PLEASE HELP
Thanks Addam
I really need your help fast I need several parts for my 415 MS and some square parts.
Does anyone know a shop that sends fast to australia and must take Pay pal
I need aftermarket Bumper and suspension arms number Tamiya 51104 Plus some suspension mounts
PLEASE PLEASE HELP
Thanks Addam
Tech Master
Originally Posted by TRFMAD
Hi Guy's
I really need your help fast I need several parts for my 415 MS and some square parts.
Does anyone know a shop that sends fast to australia and must take Pay pal
I need aftermarket Bumper and suspension arms number Tamiya 51104 Plus some suspension mounts
PLEASE PLEASE HELP
Thanks Addam
I really need your help fast I need several parts for my 415 MS and some square parts.
Does anyone know a shop that sends fast to australia and must take Pay pal
I need aftermarket Bumper and suspension arms number Tamiya 51104 Plus some suspension mounts
PLEASE PLEASE HELP
Thanks Addam
Drop them a mail: [email protected]
Originally Posted by Tek Nickal
Which suspension blocks do you use to run the short arms? All numbers for the blocks get confusing.
The blocks are 1B - 1A in the front and 1XB - 1D in the rear....
Tech Master
iTrader: (12)
Thanks Mate
Thank you for your prompt help Ben.C
Addam
Addam
Tech Master
Originally Posted by TRFMAD
Thank you for your prompt help Ben.C
Addam
Addam
Your welcome... I guess Japan will be fast. Since they are in our Asia Pac region.